View source for Book Bootsmotorenbau im ostdeutschen binnenland (bis 1945)

BOOTSMOTORENBAU IM OSTDEUTSCHEN BINNENLAND (BIS 1945) 

BY WOLFGANG RUDOLPH

(Translated by Google)


The present presentation deviates from the scheme of the two earlier regional contributions on engine construction on the German coasts (Baltic Sea Coast 1996, North Sea Coast 1997). 

In this third part of the investigation, many personal details and a number of desirable details about the respective productions had to remain open. They could no longer be elucidated: the loss of archive material during and after the Second World War was too great, and many things were also destroyed senselessly during reunification (1990). 

The main sources were the German Reich address book for industry and commerce, the German Reichsanzeiger, the handbook of German stock corporations, the handbook of limited liability companies (GmbH) and a large number of local address books and official telephone directories - in addition to the advertising pages of the leading ones German trade journals (between 1895 and 1945): Werft Reederei Hafen, communications from the German Sea Fishing Association, German fish industry, gas engine technology, the oil engine/the economic engine, the motor car, the yacht, motor ship/motor boat and canoeing. Two standard works on German automotive history proved to be interesting new source material (Seherr-Thoss 1974, Gränz & Kirchberg 1975). In the present study, however, only those manufacturing companies are listed for which - e.g. in the cases of Nacke (Coswig), Hering (Ronneburg), Elite (Brand) or VOMAG (Piauen) and FAMO (Breslau) - in advertisements, internal documents or articles in the trade press expressly referred to the use of the manufactured engines as boat or ship propulsion systems. In principle, many older truck engines and car drives could be converted for installation in ships without any major changes. Basically, the not inconsiderable military-technical part of the engine production during the two world wars remains unconsidered: e.g. at Steudel (Kamenz) to drive engineer pontoons and assault boats, at FAMO during the defense of the Breslau Fortress, but also at Klingebiel (Schwerin), Grade (Magdeburg) , VOMAG
(Plauen) and others.


The preservation of boat engines in museums in the east German inland is much worse than in the coastal federal states: Of the 37 companies documented here, only examples of the five brands Buckau Wolf, Jaehne, Junkers, Leisnig and Raab have survived - all as Accidental acquisitions, by no means as a result of systematic search and collection.

In contrast to the first two parts, in this overview the productions are presented in the alphabetical order of the 3 1 production places. However, due to its size (with around 60 manufacturers), the Greater Berlin area must be dealt with as Part IV in the next volume.

With regard to the regional development history, it should only be briefly mentioned that the earliest special boat engines were made in the eastern German inland territories.


Regarding the regional development history, it should only be mentioned briefly that in the eastern German inland territories the earliest special boat engines were manufactured in places where one would hardly expect it today: in Magdeburg (Langen Siepen 1891 ), in Leipzig (roughly 189  ), also in Coswig near Dresden (Nacke 1901 ). 

But then the Berlin trade quickly followed suit - from 1901 with Dürr and Kämper. German outboard engine construction began its triumphal procession from Berlin: initially as a rear engine (FZ Ziegenspeck 1913, Hasse 1913), later as a side-board engine (König 1925). Covering the needs of the Navy also allowed the new type of small machine construction to flourish in Schwerin (Klingebiel), Magdeburg (Grade), Aschersleben (Trumann), Zeitz (Raab), Frankfurt/Oder and Kamenz (Steudel). Before starting the production of boat drives, there were often quite different types of production, e.g. precision mechanical construction of orchestras (at Grob and Raab), special machine construction (pumps at Langensiepen, safes at Trumann, straw processing plants at Nacke). During the transition from the increasingly heavy-duty Otto ship engines to light vehicle diesel engines, production in the East German states and provinces was very significantly influenced by the developments at Junkers (Dessau, Breslau and Scharfenstein). The last hot-bulb boat engines from the eastern interior were delivered in 1940 to Leisnig in Saxony.


Production sites and manufacturing companies

The 31 production sites dealt with here are spread over the following East German territories:

Aschersleben

Böhlitz-Ehrenberg

Brand-Erbisdarf

Breslau 

Chemnitz 

Coswig

Dessau

Dresden 

Eilenburg 

Eisenach 

Erfenschlag 

Erfurt

Frankfurt (Oder) 

Görlitz

Gössnitz

Hirschberg

Kamenz

Landsberg (Warthe)

Leipzig

Leisnig 

Magdeburg 

Niesky 

Nordhausen 

Plauen 

Potsdam 

Ronneburg 

Scharfenstein 

Schwerin 

Stettin

Zeitz 

Zschopau 

== Aschersleben - Trumann ==
In 1891, master locksmith Wilhelm Trumann - who had apparently moved here from the surrounding area - established himself in the Hermann Krone workshop in Aschersleben and traded there as "Locksmith and safe factory", since 1918 also as a manufacturer of motor ploughs, motor locomotives and commercial engines - in a second part of the factory. That may have happened after the takeover of specialists from »Ascherslebener Maschinenbau AG (formerly W. Schmidt & Co.)«, which - known as a specialist for high-pressure superheated steam engines - also manufactured large stationary diesel systems after 1908. This company merged with the Magdeburger Maschinenfabrik Buckau in 1917 and was then shut down in stages. By 1920 at the latest, the Trumann works had also expanded their production to include one- and two-cylinder hot-bulb engines as boat and ship drives. From 1925, diesel engines were also manufactured there based on Benz patents: in one to three-cylinder versions from 16 to 54 hp.

The design of Trumann's company logo, "Double Man with Key Head in the Gear Ring," was peculiar. In 1928 Trumann AG (since 1921) had to file for bankruptcy and was dissolved the following year. From 1930 onwards, the successor company traded under the name "Safety and Truco Steel Furniture Factory" even after the Second World War. In 1990 the company had to close and the area had to be sold.
[[Category:BOOKS]]